Megaİzo Lastik 10 S103

• Fit for contact with drinking water.
• Highly adhesive.
• Being of water repellant nature, the product is resistant to water and frost.
• Ensures seamless waterproofing for application surfaces.
• Allows for the application of any coating material subsequent to the application thereof.
• Fully elastic.
• Applied rapidly and easily.
• Does not contain solvents, and is environmentally friendly.

Usage Areas

• MegaIzo Lastik 10 S103 is applied for waterproofing before the top coating material in such wet spaces as bathrooms, kitchens and balconies, in terraces, and in such constantly wet spaces as pools and water tanks. It is suitable for use on horizontal and vertical surfaces of indoors and outdoors spaces.
  

  ---

  Technical Informations

  • PerformanceTYPE: CM O2 P, Cementitious liquid-applied water impermeable product with improved crack bridging ability at very low temperature (−20°C) and resistant to contact with chlorinated water.

    Initial adhesion strength: ≥ 0.5 N/mm² (TS EN 14891 : A.6.2)
    Adhesion strength after water contact: ≥ 0.5 N/mm² (TS EN 14891 : A.6.3)
    Adhesion strength after thermal ageing: ≥ 0.5 N/mm² (TS EN 14891 : A.6.5)
    Adhesion strength after freezing – thawing cycles: ≥ 0.5 N/mm² (TS EN 14891 : A.6.6)
    Adhesion strength after hard water contact: ≥ 0.5 N/mm² (TS EN 14891 : A.6.9)
    Waterproofing: No penetration, ≤ 20 gr increase in mass (TS EN 14891 : A.7)
    Crack bridging capability under standard conditions: ≥ 0.75 mm (TS EN 14891 : A.8.2)
    Adhesion strength after chlorinated water contact: ≥ 0.5 N/mm² (TS EN 14891 : A.6.7)

    The foregoing values represent the results of the laboratory tests conducted at 23 ± 2°C temperature and 50% ± 5 relative humidity conditions. The values provided as per the table may vary depending on the surface and ambient conditions.

    Application LimitsUseful time for prepared mixture – Pot life: Maximum 3 hours
    Stand by period between coats: Minimum 6 hours
    Required standby time before subsequent application: Minimum 3 days

    The foregoing values represent the results of the laboratory tests conducted at 23 ± 2°C temperature and 50% ± 5 relative humidity conditions.
    The values provided as per the table may vary depending on the surface and ambient conditions.

    Technicial Specificationsa. Chemical Structure: Cement and polymer emulsion based waterproofing material
    b. Mortar Density: 1,70 ± 0.01 gr/cm³
    c. Application Thickness: 2 – 3 mm
    d. Color: Powder: Gray, Liquid: Milk white

    Mixing RatioThe powder component (20 kg) and the liquid component (10 kg) should be thoroughly mixed.
    b) Mixing Equipment
    • Low speed electrical mixer (400 cycles/ min.)
    • Special tip stirring equipment
    c) Mixing Period
    Mixing with a low speed mixer should be continuously done by slowly adding the powder component into the liquid component. The components should be mixed until it gets homogenous without any dry dust or lump left.The mortar should, then, be stirred once again for 1 to 2 minutes after being had settled for 3 to 4 minutes following preparation.
    d) Application Equipment
    • Brush
    • Trowel
    e) Equipment Cleaning
    The equipment used should be cleaned with water following the application before the product dries.

    ConsumptionRecommended consumption amount for 2 mm film thickness; 3.0 – 3.8 kg/m². The said values may vary, depending on the surface and ambient conditions.

    PackagingMegaIzo Lastik 10 S103 is delivered as a set of 20 kg craft bag, containing powder component, and 10 kg plastic drum, containing liquid component.

    Reference Standardsa. Certifications / Standards
    • TS EN 14891
    • TS EN 1504 – 2
    b) Ministry of Public Works and Settlement Item No.
    • Ministry of Public Works and Settlement Item No.: 04.477/2

    Quality Certificate
    Certificate of “Suitability for use in contact with water intended for human consumption” granted according to BS 6920:2000 standard by WRAS (Water Regulations Advisory Scheme) (Certificate No: 1105546)
    • TSE– CM O2 P
    • CE

    ---

    Application Procedure

    • Application Surfaces
      Indoors and Outdoors Walls;
      • Cement based plaster (MegaFilm A201 primer applied)
      • Concrete (MegaFilm A201 or MegaFilm BB A204 primer applied)
      Indoors and Outdoors Floors;
      • Cement based trowel coating (MegaFilm A201 primer applied)
      • Concrete (MegaFilm A201 or MegaFilm BB A204 primer applied)

      Surface Preparation :
      • Application surfaces should be sound, clean, dust-free, and free from molding oils and other foreign substances. Such materials as mortar and cement residues should be peeled off.
      • The surface defects, which are deeper than 1 cm, should be repaired with MegaTamir I T101 or MegaTamir K T102 6 – 8 hours in advance. In the cases, where structural repair mortar should be used; MegaTamir I Yapısal T103 or MegaTamir K Yapısal T104 should be preferred.
      • Edge and corner joints should be beveled with MegaTamir I T101 and MegaTamir K T102 repair mortars in order for the maintenance of waterproofing.
      • In the cases, where beveling is not performed; MegaIzo Bant S901 should be applied to such inadequately waterproof spots as edge and corner joint spots in order to ensure the maintenance of insulation.
      • Upon the completion of the surface cleaning, MegaFilm A201 primer should be applied in a single coat with a brush and be left to dry for 1 to 2 hours in order to enhance the bonding strength and stabilize the surface absorption.
      • Exposed concrete surfaces should be applied MegaFilm BB A204 exposed concrete primer in single coat and be left to dry for minimum 3 hours prior to the application of the adhesive mortar in order to enhance the adhesion strength.

      Application Methods :
      • Megaİzo Lastik 10 S103 product, for which the mixture has been prepared, must be applied on the surface in at least two layers with dry film thickness of 2 mm. The application of the second layer and the layers after that must be made after the first layer is fully dry and in perpendicular direction to the previous application.
      • Depending on the nature of the application surface; the secondary coat may be applied after the placement of MegaIzo File S902 on the primary coat. In the cases, where net reinforcement is necessary; the net shall be laid on the primary coat before it dries.
      • For coating processes over isolation on grounds where water proofing is done, use C2 and S1/S2 class adhesive with high performance according to TS EN 12004 standards.

      Application Recommendations :
      • Due care must be taken to ensure that the insulation material is not damaged by mechanical impacts in the cases of coating over the insulation.
      • The product should not be applied against negative water pressure.
      • The product should, once mixed, be used before the expiration of its pot life. Any product, the pot life of which has expired, should not be used during the application.
      • Any foreign material should not be added into the product’s components of the product during the application.
      • The product should not be applied on unsound surfaces. The soundness and the load bearing capacity of old surfaces should be checked prior to adhesion.
      • The surface should be preserved from air currents and water contact during and after the application.
      • The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing.
      • Due care should be given to prevent the exposure of the material to direct sunlight in hot weather conditions.
      • The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance.
      • The product should not be applied in rainy weather conditions, and the application surface should be preserved from rain for a period of 24 hours.
      • Refer to our technical support hotline for recommendation on different surface applications. (PHONE: 444 4 595)

      Surface and Ambient Temperature
      The surface and ambient temperature should be between +5°C and +35°C whilst at application.