MegaTamir T106

• Protects reinforcement steel against corrosion.
• Used as the binder primer prior to repair mortar applications.
• Single component product and is used after mixing with water.
• Water and frost resistant.
• Prepared and applied easily.

Usage Areas

• MegaTamir T106 is used as the anticorrosion primer for iron and steel reinforcement, and also it is used as adherence enhancing primer and coating material on cement based surfaces.
  

  ---

  Technical Informations

  • PerformanceCompressive strength: ≥ 25 MPa (R3) (TS EN 196 – 1)
    Bonding through adhesion: ≥ 1.5 – 2.5N/mm² (TS EN 1542)

    The foregoing values represent the results of the laboratory tests conducted at 23 ± 2°C temperature and 50% ± 5 relative humidity conditions. The values provided as per the table may vary depending on the surface and ambient conditions.

    Application LimitsUseful time for prepared mortar – Pot life: Maximum 1,5 hours

    The foregoing values represent the results of the laboratory tests conducted at 23 ± 2°C temperature and 50% ± 5 relative humidity conditions. The values provided as per the table may vary depending on the surface and ambient conditions.

    Technicial Specificationsa) Chemical Structure: Cement based anticorrosive mortar and adherence primer
    b) Color: Gray
    c) Application Thickness: 1 mm at single coat. Coatings on steel surface should be applied in 2 coats.
    d) Stand by period between coats 4 – 5 hours

    Mixing RatioThe product should be mixed with water, weighing equal to 27 – 29 % of the product. (5,4 – 5,8 liters of water for a 20 kg package)
    Mixing Equipment
    • Low speed electrical mixer (400 cycles/ min.)
    • Special tip stirring equipment
    Mixing Period
    The product should be stirred with a low speed mixer until any dry dust and globs are eliminated. The mortar should, then, be stirred once again for 1 to 2 minutes after being had settled for 3 to 4 minutes following preparation.
    Application Equipment
    • Brush
    • Roller
    Equipment Cleaning
    The equipment used should be cleaned with water following the application before the product dries.

    ConsumptionRecommended consumption amount for 1mm film thickness is 2,0 kg/m2. The said value may vary, depending on the surface and ambient conditions.

    PackagingMegaTamir T106 is delivered in net 20 kg craft bags, which are stowed in 60 pcs. on a 80 x 100 cm palette (1200 kg).

    Reference Standardsa. Certifications/ Standards
    • TS EN 1504-7
    Ministry of Public Works and Settlement Item No.
    • Ministry of Public Works and Settlement Item No.: 04.613/8-a

    Quality Certificates
    • Conformant to TS EN 1504 – 7 / R3

    ---

    Application Procedure

    • Application Surfaces
      Indoors and Outdoors Walls;
      Concretebr
      – Iron – steel reinforcement Indoors and Outdoors Floors;
      Concretebr
      – Iron – steel reinforcement

      Surface Preparation:
      Corrosion Prevention:
      • The application surface should be dry, clean, sound and dust free, and should have been cleansed of oil, dirt or any materials that may prevent adhesion, and any such materials as mortar and cement residues should be scraped from the application surface. If necessary, degreasing agents should be used.
      • The first coat is applied with a brush or roller of moderate hardness, with a thickness of 1 mm to the cleaned reinforcement. The second coat is applied in the same thickness after the first coat is completely dry
      Adherence Enhancing:
      • The application surface should be dry, clean, sound and dust free, and should have been cleansed of oil, dirt or any materials that may prevent adhesion, and any such materials as mortar and cement residues should be scraped from the application surface.
      • Surface water should be waterlogged so that there is no free water on the surface. For very absorbent surfaces, 2nd coat application should be done after 1st coat is completely dry.
      • Repair mortar application, should be done before MegaTamir T106 is completely dried.

      Application Methods:
      •MegaTamir T106 should be applied without exceeding 1 mm on each coat. The second coat should be applied after the first coat dries for very absorbent surfaces.

      Application Recommendations :
      • The product should, once mixed, be used before the expiration of its pot life. Any mortar, the pot life of which has expired, should not be used during the application.
      • Any such foreign substance as lime, cement or plaster should not be added to the mortar prepared.
      • Any extra water should not be added to the mixture.
      • The product should not be applied on unsound surfaces. The soundness and the load bearing capacity of old surfaces should be checked prior to adhesion.
      • The surface should be preserved from air currents and water contact during and after the application.
      • The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing.
      • Due care should be taken to ensure that the material is not exposed to direct sunlight in hot weather conditions, and the product should be mixed with cold water.
      • The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance.
      • The product should not be applied in rainy weather conditions, and the application surface should be preserved from rain for a period of 12 hours.
      • Refer to our technical support hotline for recommendation on different surface applications. (PHONE: 444 4 595)

      Surface and Ambient Temperature
      The surface and ambient temperature should be between +5°C and +30°C whilst at application.